This is a demo store. No orders will be fulfilled. english
Begadi PRO 60° "SHP5" HPA / AEG Flat Hop Bucking / Rubber (Air Sealed, for approx. 5mm Barrelwindow) -blue-
Other interesting articles:
The SHP series are new developed HopUp buckings / rubbers from Begadi, designed in Germany!
They are specially designed for modern HPA/AEG/S-AEG guns and HopUp Units - and have some special features to increase the range and decrease the grouping:
The SHP series is an addition to the already available FLY and MAG HopUp rubbers and was specially developed for HPA systems. Due to the revised seal, the SHP series is also compatible with certain AEGs, you can find a comparison below in the description.
Patch:
Our patch of the SHP5 rubber is identical to the FLY5 and has a radius of 2.5mm (5mm diameter). This is therefore smaller than the BB itself and thus ensures that the BB is precisely centered in the barrel.
The BB is also kept straight when it is fired to prevent it from escaping to the side. In order to generate a constant hop effect, the braking effect decreases in the front area.
Orientation:
To prevent the bucking from twisting on the barrel, there are two supports on the inside. These rest on the barrel and support alignment and installation.
Thus, the built-in tensioner can press the patch inside straight onto the BB, which also prevents outliers to the side. Note that a BB can only fly straight if the weapon is also held straight.
Seal & Comparison:
Here lies the difference between the available HopUp rubbers. Especially with HPA systems, it often happens that the built-in nozzle cannot be changed and is therefore not compatible with every rubber. This is where our SHP series comes into play.
Our existing FLY and MAG rubbers have a slightly larger seal, making them compatible with flat nozzles. (e.g. Begadi PRO Nozzle with double O-ring).
However, some manufacturers use a pointed nozzle in their guns. If this is the case, the nozzle had to be replaced or its length adjusted. In the SHP series, the seal has been made smaller, which means that pointed nozzles no longer have to be changed.
Note: For a flat or round nozzle we still recommend the FLY or MAG series, for pointed nozzles the SHP series should be used.
Our SHP series also offers two increases in the front area: At these points, our rubbers/buckings have a diameter of 9.80 mm, which press into the hop-up unit during installation and therefore no pressure is lost.
Durability and Wear:
All of our Begadi PRO buckings are made from a very robust and durable rubber compound. This keeps the set hop-up effect constant over a long period of time and wears out much more slowly than conventional rubber. Even with disassembly or maintenance, you don't have to worry about the rubber getting cracks on the patch. You should still exercise some caution when removing it. Please note the correct selection of the hardness for your weapon (energy and bullet weight). If a rubber that is too soft is selected, wear will increase!
Marking/Hardening:
In order to be able to tell our buckings apart, the respective version is marked directly. The rubber compound (hardness) is reflected in the colour: 50° green - 60° blue - 70° black. This means that you can immediately see each version.
Tensioner:
We have also developed suitable tensioners for our buckings, these are precisely matched. If our tensioners are not compatible with your HopUp Unit, please use Flat Hop Tensioners.
Recommendation:
- Begadi PRO 70° HopUp Tensioner (D=3mm) -5mm- for barrels with standard (ca. 5mm) Barrelwindow
- Begadi PRO 70° HopUp Tensioner (D=2,5mm) -5mm- for barrels with standard (ca. 5mm) Barrelwindow
Zeroing in:
Like all other buckings available on the market, ours need to be zeroed in. A constant hop-up effect is achieved after about 200 - 400 shots. (Depending on the energy and BB weight)
Avoid setting too much hop on the first 2 magazines as the patch will need to settle in.
Special case Begadi Sport M14 / Cyma M14:
Cyma's M14 uses a significantly shorter bucking. Our normal FLY5, FLY7, MAG5, MAG7 can be used here, but the rubber must be cut off at the front (towards the muzzle) by 2 - 3mm. If you don't want to do this yourself, we already offer a pre-cut variant. - Item 26021016
Suggested hardness:
Compatibility:
In the following table we would like to give you a brief overview of which HopUp Unit we recommend for which bucking. Please note that there may be differences depending on the manufacturer and the weapon!
In most cases, only the nozzle length needs to be adjusted here. Unfortunately, we cannot go into all the guns on the market here, since the barrel used, the tappet plate, the sector gear and the shell also have an influence on the required nozzle length.
The buckings marked with green are compatible with the original nozzle length, marked with white means that the nozzle length has to be adjusted (changed).
Overview of the different versions of our PRO Buckings:
Size information (outside) for the FLY series [FLY + SHORT]:
Size information (patch) for the FLY5 + FLY7 series:
3D representation / interior view of the FLY5 + SHORT series:
They are specially designed for modern HPA/AEG/S-AEG guns and HopUp Units - and have some special features to increase the range and decrease the grouping:
The SHP series is an addition to the already available FLY and MAG HopUp rubbers and was specially developed for HPA systems. Due to the revised seal, the SHP series is also compatible with certain AEGs, you can find a comparison below in the description.
Patch:
Our patch of the SHP5 rubber is identical to the FLY5 and has a radius of 2.5mm (5mm diameter). This is therefore smaller than the BB itself and thus ensures that the BB is precisely centered in the barrel.
The BB is also kept straight when it is fired to prevent it from escaping to the side. In order to generate a constant hop effect, the braking effect decreases in the front area.
Orientation:
To prevent the bucking from twisting on the barrel, there are two supports on the inside. These rest on the barrel and support alignment and installation.
Thus, the built-in tensioner can press the patch inside straight onto the BB, which also prevents outliers to the side. Note that a BB can only fly straight if the weapon is also held straight.
Seal & Comparison:
Here lies the difference between the available HopUp rubbers. Especially with HPA systems, it often happens that the built-in nozzle cannot be changed and is therefore not compatible with every rubber. This is where our SHP series comes into play.
Our existing FLY and MAG rubbers have a slightly larger seal, making them compatible with flat nozzles. (e.g. Begadi PRO Nozzle with double O-ring).
However, some manufacturers use a pointed nozzle in their guns. If this is the case, the nozzle had to be replaced or its length adjusted. In the SHP series, the seal has been made smaller, which means that pointed nozzles no longer have to be changed.
Note: For a flat or round nozzle we still recommend the FLY or MAG series, for pointed nozzles the SHP series should be used.
Our SHP series also offers two increases in the front area: At these points, our rubbers/buckings have a diameter of 9.80 mm, which press into the hop-up unit during installation and therefore no pressure is lost.
Durability and Wear:
All of our Begadi PRO buckings are made from a very robust and durable rubber compound. This keeps the set hop-up effect constant over a long period of time and wears out much more slowly than conventional rubber. Even with disassembly or maintenance, you don't have to worry about the rubber getting cracks on the patch. You should still exercise some caution when removing it. Please note the correct selection of the hardness for your weapon (energy and bullet weight). If a rubber that is too soft is selected, wear will increase!
Marking/Hardening:
In order to be able to tell our buckings apart, the respective version is marked directly. The rubber compound (hardness) is reflected in the colour: 50° green - 60° blue - 70° black. This means that you can immediately see each version.
Tensioner:
We have also developed suitable tensioners for our buckings, these are precisely matched. If our tensioners are not compatible with your HopUp Unit, please use Flat Hop Tensioners.
Recommendation:
- Begadi PRO 70° HopUp Tensioner (D=3mm) -5mm- for barrels with standard (ca. 5mm) Barrelwindow
- Begadi PRO 70° HopUp Tensioner (D=2,5mm) -5mm- for barrels with standard (ca. 5mm) Barrelwindow
Zeroing in:
Like all other buckings available on the market, ours need to be zeroed in. A constant hop-up effect is achieved after about 200 - 400 shots. (Depending on the energy and BB weight)
Avoid setting too much hop on the first 2 magazines as the patch will need to settle in.
Special case Begadi Sport M14 / Cyma M14:
Cyma's M14 uses a significantly shorter bucking. Our normal FLY5, FLY7, MAG5, MAG7 can be used here, but the rubber must be cut off at the front (towards the muzzle) by 2 - 3mm. If you don't want to do this yourself, we already offer a pre-cut variant. - Item 26021016
Suggested hardness:
| Bucking/Version | Energy/Weight |
| FLY5 Regular, SHP5 and SHORT - 50° Green | 0,5 - 1,3 Joule with 0,20 - 0,28g BBs |
| FLY5 Regular, SHP5 and SHORT - 60° Blue | 1,2 - 2,0 Joule with 0,25 - 0,36g BBs |
| FLY5 Regular, SHP5 and SHORT - 70° Black | 1,9 - 2,5 Joule with 0,32 - 0,40g BBs |
| FLY7 - 50° Green | 1,3 - 1,8 Joule with 0,30 - 0,40g BBs |
| FLY7 - 60° Blau | 1,5 - 2,8 Joule with 0,36 - 0,45g BBs |
| FLY7 - 70° Black | 2,5 - 3,5 Joule with 0,45 - 0,48g BBs |
| MAG5 - 50° Green | 1,0 - 1,5 Joule with 0,28 - 0,36g BBs |
| MAG5 - 60° Blue | 1,4 - 2,0 Joule with 0,32 - 0,45g BBs |
| MAG5 - 70° Black | 1,9 - 2,5 Joule with 0,36 - 0,48g BBs |
| MAG7 - 50° Green | 1,3 - 1,8 Joule mit 0,30 - 0,40g BBs |
| MAG7 - 60° Blue | 1,5 - 2,8 Joule with 0,40 - 0,48g BBs |
| MAG7 - 70° Black | 2,5 - 3,5 Joule with 0,40 - 0,48g BBs |
Compatibility:
In the following table we would like to give you a brief overview of which HopUp Unit we recommend for which bucking. Please note that there may be differences depending on the manufacturer and the weapon!
In most cases, only the nozzle length needs to be adjusted here. Unfortunately, we cannot go into all the guns on the market here, since the barrel used, the tappet plate, the sector gear and the shell also have an influence on the required nozzle length.
The buckings marked with green are compatible with the original nozzle length, marked with white means that the nozzle length has to be adjusted (changed).
Overview of the different versions of our PRO Buckings:
Size information (outside) for the FLY series [FLY + SHORT]:
Size information (patch) for the FLY5 + FLY7 series:
3D representation / interior view of the FLY5 + SHORT series:
Review Partner